- #2017 mac mini hard drive upgrade for mac
- #2017 mac mini hard drive upgrade serial
- #2017 mac mini hard drive upgrade full
- #2017 mac mini hard drive upgrade pro
- #2017 mac mini hard drive upgrade free
Use the four screws to secure the drive in place and reattach the ribbon cable. With the hard drive in place, it's now time to place the CD drive back into the Mac Mini. Replace the four screws to secure the drive and reattach the temperature sensor - it should have enough adhesive left on it to stick. There are two anti-static cushions on the back of the hard drive, peel both of these cushions off of the old drive and place them onto your new one, which you can then slide into the slot. Gently lift the sensor, move the wire to the side, slide the drive up slightly, and remove it using the tweezers. There is a temperature sensor on the top of the drive and a wire running down the left side. It's held in with four screws, two on the top and two on the side. The hard drive is on the back of the CD drive. Make sure you are removing the screws that connect the drive to the case and not the ones on the actually CD drive. Unscrew the four screws that hold the CD drive into place and detach the ribbon cable on the top of the drive. The hard drive is located on back of the CD drive. Under each antenna are springs - don't lose these as they are required when reassembling the device. The two smaller ones on the left simply lift out, while larger one on the right must be squeezed from the bottom. Next, you have to remove the three antennas. You will hear a faint pop as the clips become dislodged, at which point the cover can be lifted off. Bend the knife away from you as you slowly work your way around all fours edges of the device. Gently shimmy the knife in between the base of the Mac Mini and the case. The cover on the Mac Mini is held in place with small clips that must be dislodged with the putty knife.
#2017 mac mini hard drive upgrade free
Your current drive (if it's still functional) can be backed up using a program like Apple's Time Machine or the free utility SuperDuper. I also recommend picking up a can of compressed air to clean out the dust that has built up throughout the years.
#2017 mac mini hard drive upgrade serial
Pre-2010 Mac Mini models support a single Serial ATA drive with speeds of 3 GB/s. You will need a putty knife or small paint scraper to remove the Mac Mini's casing, a Phillips head #2 screwdriver, a pair of tweezers, and either a replacement 2.5-inch solid-state drive or a hard drive with a height of no more than 9.5mm. Apple redesigned the Mac Mini line in 2010 to include a removable cover that gives users quick and easy access to the hard drive and memory.
#2017 mac mini hard drive upgrade for mac
Here's what you need to know: Note: This how-to guide is for Mac Mini models from 2005 through 2009.
#2017 mac mini hard drive upgrade full
Rather than spending $600 on a newer model, you can swap out your full or faulty hard drive for a newer and faster one. There isn't a real need to upgrade, though. We were one of them, but wouldn't you know it, the hard drive in our 2009 Mac Mini has taken its last breath. Given that Apple doesn't give Mac Mini owners many reasons to upgrade, there are a still a good amount of happy customers using older models.
#2017 mac mini hard drive upgrade pro
In fact, the latest model hasn't even been updated to include Intel's newer and more efficient Haswell processors, despite the iMac, Macbook Air, and Macbook Pro receiving updates. Since it first debuted in 2005, the small computer has only seen one major redesign in 2010, and is often left out of the company's dazzling press events. not towards the open side of the base plate, this is not immediately noticeable when the SSD is installed.The Mac Mini is like Apple's forgotten stepchild. Because this is the side between the keyboard and the board, i.e. In the worst case (as in our case), it then dissolves in the MacBook and causes errors. So take a closer look at your copy and if the plate isn’t really soldered on, remove it carefully, it’s superfluous anyway. However, this is partly only glued and not soldered, because due to technical progress there are simply no more memory chips on one side (depending on the size). We have one more tip: some models have a metal plate on the back so that the new SSD looks like the old one in the MacBook. Remove the metal plate that is only for the optics We have described the entire process of installing a new SSD here in detail. This makes the exchange extremely simple and the MacBook finally has enough storage space.
Or – we recommend this solution because it is not much more expensive – an OEM replica of the Apple SSD: Here on Aliexpress you can find SSDs in OEM quality. March 2022 at 15:27 - Image source: Amazon Affiliate Program.